MasterForm Hobs
MasterForm cast-in hobs are provided with hob legs pre-set to the required slab depths. Our hobs sit on top of the proprietary Klipmaster hob legs, when pressure is applied the hob simply and securely clips into place. Any reinforcement details are to be designed by the project engineer.
MasterForm post-fix hobs are quick and easy to install and are a fully cast-in system therefore saving time on stripping.
MasterForm post fix hobs are installed with M8 x 100mm concrete screws at each hob spacer location (approx. 500mm crs.). Any reinforcement requirements are to be designed by the Project Engineer.
MasterForm supply straddle brackets that adapt to the profile of the metal formwork system that are using. Simply confirm your profile with MasterForm.
As long as the wet concrete is uniformly placed around the support legs then very little movement is usually experienced. Legs taller than 300mm usually require some stabilization with tie wire. We also suggest some simple tie wire cross supports on the hob lengths as the guys on site feel necessary.
MasterForm hobs are 3m long.
Yes. MasterForm will extract the profile directly from the architectural DWG background and supply you with a keyplan for quick and accurate installation.
MasterForm will provide you with 25mm plastic bar chairs to sit beneath the support legs to ensure a class 2 soffit.
MasterForm hobs are supplied with corners, joiners and end caps for a quick and tidy finish.
Simply send through your concrete profile plans and structural GA plans and MasterForm can schedule your project for you.
Yes. All MasterForm hobs are manufactured with G275 Galvanized steel. MasterForm can provide you with warranted systems from a number of suppliers recommended for use on our hobs upon request. Nothing more onerous than off-form hobs.
Typically 5-7 days from shop drawing approval however shorter time frames are possible.
All MasterForm hobs are manufactured in Melbourne and shipped anywhere in Australia on an express service.
MasterForm is Australia’s leading hob manufacturer. Our hobs have been used on projects all over the country including, Westside place Melbourne, Aurora in Melbourne, Capital Grand in Melbourne, The ribbon in Sydney, ParkOne in Sydney.
MasterForm Hobs create an accurate and consistent hob profile that is easy for filling. The pre-fabricated hob eliminates the warping and twisting of timber formed hob. MasterForm Hobs also eliminates the need for coming back and stripping the timber away from the hob once the concrete is cured, saving considerable amounts of time.
Rapid Rebates
Simply send your concrete profile plans through to MasterForm for an obligation-free schedule and quote.
Yes. MasterForm can provide you with a number of warranted systems form various manufacturers that have been tried and tested on our products.
Yes. Any depth is available.
As long as the wet concrete is uniformly placed around the support legs then very little movement is usually experienced. MasterForm normally manufacture slightly oversize to allow some tolerance.
Time, quality and cost will all be improved by using the system.
Typically 5-7 days from approval of shop drawings.
Yes. MasterForm will take these radius profiles directly from the architectural DWG to ensure perfect co-ordination.
Yes. Rapid rebates usually come as single assembly and the legs are pre-set to a height for rapid installation. No stripping is required which further saves time.
Yes. As the rapid rebates are cast-in then the possibility of Edge divots that are created from stripped rebate systems is completely eradicated. The top and bottom of the profile also sets a datum for flatter and more accurate slabs.
Ezy EdgeForm
Send through your conc profile DWG files and Str GA’s/PT GA’s and we will coordinate.
Yes. Our Ezy Edge Form systems are designed for multiple re-use. The tallest we have gone is 99 stories and still working.
No. We only recommend and will only supply an Ezy Edge Form system if it can amortized through multiple re-use to a point that is more economical than ply.
Typically four weeks form PO.
Aurora in Melbourne, ParkOne is Sydney, 101 Moray St Port Melbourne, Monash Chancellery in Melbourne, Castle residence In Sydney and many more.
We generally design to less than 20KG per segment so that they can be man handled on site.
MasterForm always produce a key plan for quick and easy installation. Segments are screwed/nailed down and bolted together with bolts provided by MasterForm.
Perimeter hobs and rebates are common and we have systems for all whether straight, radius or segmented.
Safety Peno
Yes. MasterForm unique patented design allows for the safety mesh to be cast into the slab allowing for 5Kpa UDL and 2.5 KN point load over a 200mmx 100mm footprint imposed load.
1600mm in any one dimension.
MasterForm penos have been certified by Warrington fire for use with the promat Bulkhead Batt system.
Up to 1m deep-with ribbing.
You can prepare a schedule of sizes or get MasterForm to assist by sending your plans through.
Yes. The unique MasterForm perimeter profile casts in seamlessly with the surrounding concrete.
Typically services can run through the 100x 100 aperture rated mesh to keep it safe for fit-out trades without having to work though handrails. Alternatively locally remove some mesh on site.
Yes. MasterForm will identify this and nominate details on the take-off sheets.
Not a problem. MasterForm incorporate a rated flat side that requires anchor screws on site.