At Masterform we are continually providing and refining solutions for the issues that building sites face everyday.
We have been able to harness our experience over the years and develop systems for the industry as a whole – all with the intent to speed up pour cycles and provide better detailing to concrete slabs.
There is rarely a one-size fits all solution out there but we have (almost) seen it all over the years so rest assured that you are in safe hands.
Our metal plinths are fabricated to suit your project requirements and can be supplied with supporting legs to allow for a monolithic pour with your slab, or they can be post fixed to an existing slab in a retrofit scenario. No stripping required.
A cast-in metal set down formwork system which speeds up the process of establishing set downs in concrete and eliminates the need to strip any formwork.
Requiring only a few minutes to setup, this system is extremely cost effective and fast to install. Our cast-in supporting legs are custom made to suit the required slab depth. No need to strip, just set and forget.
Our Cast-in Edgeform is the quickest way to setup a suspended slab stop end.
Custom made to suit project requirements with no need to strip. Perfect for forming up against existing walls or inaccessible areas. Available with or without gussets depending on depth
Our Cast-in Edgeform with Hob is perfect for slab edges the quickest way to setup a suspended slab stop end and can be supplied with integral hob if project requirements dictate.
Can include ferrules for balustrade/screen fixing. Perfect for slab edges being covered by cladding or facades.
Cast-in metal pedestal boxes to suit project requirements. Support these on cast-in legs and pour with your slab or fix directly to an existing slab.
Custom top and bottom steel plates laser cut to suit curved upstands, walls or deeper slab step geometry. Use timbers & ply to build up your shutter on site.
A cast-in metal concrete pump peno fabricated to suit project requirements.
Take the worry out of forming these odd shaped penterations up and forget about having to strip
Cast-in metal lift button boxes to suit project requirements. Provision for electrical conduits accommodated.
More accurate and cost effective than forming with foam or timber
All of our pocket formers are shop drawn to cater for your specific project requirements and are designed to be cost effective.
Custom made strippable steel crane pocket forms to suit project requirements. Designed for multiple reuses and to fit into vertical forms and jump forms.
Our proprietary plastic MF Bar Chairs are recommended for use under all of our cast-in metal legs. They provide a clean, off-form finish to the slab soffit below with no visible metal baseplate and can be stacked in 20mm increments.
No need to dread when you see data boxes on the plans any longer. These lightweight, fabricated boxes are specifically designed to create recessed pockets in the top surface of your slab.
Leg heights and cast-in box dimensions are tailored to suit product dimensions.
A cast-in product for creating edge rebates. just set and forget
Available in a variety of configurations to suit project requirements.
A lightweight, cast-in Construction Joint profile used along your prour breaks and fixed directly to the deck.
A range of key dimensions can be accommodated. Supplied in standard lengths / cut to suit on site.
A lightweight, cast-in Movement Joint profile fixed directly to your deck.
Supplied in standard lengths / cut to suit on site.
These lightweight little gems are perfect for creating edge rebates in your slabs.
Available in various widths and configurations.
This multi purpose bracket is ideal for creating perimeter hobs when screwed to edge-boards.
Available in various widths and configurations.
A strippable Construction Joint profile designed to be reused across multiple pours.
A range of key dimensions can be accommodated. Supplied in standard lengths / cut to suit on site.
A strippable Movement Joint profile designed to be reused across multiple pours.
Supplied in standard lengths / cut to suit on site.
MasterForm range of products are licensed and distributed by MasterForm System Pty Ltd
405 Francis St Brooklyn, VIC 3012
Phone: 1300 000 405
Email: info@masterform.com.au
If you require everything else for your project, contact MasterForm today by either filling in our online contact form or calling us on 1300 000 405 for a quote.
Get A Quote
